CFandM
 |
I was checking some of the bugs that were fixed in this version and came across this one. I don't know if this is related to some of the other bugs that were already present or not. To reproduce grab this filter and edit the filter and go into the group. Select the Remapper on the Intslider. Move the offset to 1 and then move the step up.....You should get a crash with a nice message...
 Stupid things happen to computers for stupid reasons at stupid times! |
|
| Posted: October 24, 2012 8:08 am | ||
|
CFandM
|
Here is the filter to use for this crash.....Submitting a report as well...
Init Switch Crash.ffxml Stupid things happen to computers for stupid reasons at stupid times! |
|
| Posted: October 24, 2012 8:08 am | ||
|
GMM
Moderator
Posts: 3491 |
Thanks CFandM, this has been reported. I also see that the "Max Value is limited" note on the IntSlider gets trimmed.
|
|
| Posted: October 24, 2012 8:49 am | ||
|
CFandM
|
Yep...Thanks Gmm, I was not sure if this one had been reported or not...
Stupid things happen to computers for stupid reasons at stupid times! |
|
| Posted: October 24, 2012 11:26 am | ||
Indigo Ray
 |
A similar int-slider bug. There's a lot of them, and I don't know if this one's new.
1. Edit the filter 2. Go into the group 3. Select the int-slider 4. Reduce the max value 5. Exit group The first bug (minor): 6. Raise the max value of the int-slider (you're out of the group now) 7. Notice the warning message underneath refers to the old max size, not the new one (also, the message is cut off) The second bug (major): 8. Try to increase the size slider past the new max value 9. FF crashes #Int1.ffxml |
|
| Posted: October 24, 2012 5:00 pm | ||
|
Indigo Ray
|
The error message (for a new max value of 10, I tried to slide to 11):
 |
|
| Posted: October 24, 2012 5:01 pm | ||
|
CFandM
|
I got that as well Indigo..Same error but different control value and range....Using your test filter.....Lots of bugs in that slider for sure....
Stupid things happen to computers for stupid reasons at stupid times! |
|
| Posted: October 24, 2012 6:05 pm | ||
Join Our Community!
Filter Forge has a thriving, vibrant, knowledgeable user community. Feel free to join us and have fun!
33,712 Registered Users
+19 new in 30 days!
153,534 Posts
+31 new in 30 days!
15,348 Topics
+72 new in year!
Online Users Last minute:
24 unregistered users.
Recent Forum Posts:
- Manson Grudge Border by Jaret by SpaceRay
12 hours ago - Kaleidoscopic Variations Vol. 2 by jhantares by jhantares
September 10, 2025 - Polygonal Images Set by Ramlyn by westdale
September 10, 2025 - FF Killing Resolution by SpaceRay
September 9, 2025 - Geometry Spinner by Rachel Duim by Rachel Duim
September 6, 2025 - Channel Glitch by Martin Naumann by SpaceRay
August 31, 2025 - Circuit Glitch by Martin Naumann by SpaceRay
August 31, 2025 - Groovy Rays by Ramlyn by Ramlyn
August 31, 2025 - Is Ultraforge dead? by dpankros
August 30, 2025 - Component Instances by AussieDecalf
August 27, 2025 - Hyperbolic Tiling Challenge by AussieDecalf
August 27, 2025 - Chaos Fields by SpaceRay
August 27, 2025
